Don't forget, all TANDEMKROSS MKIII™ series bushings come with a LIFETIME guarantee!
Steel Hammer Bushing for Mark III and 22/45 Pistols
- Magazines will slip right out
- Easier takedown and cleaning
- Can reduce failure to feeds
- Comes with colored installation instructions
This high quality 304 stainless steel bushing is made for high duty cycle shooting and replaces the Ruger® factory bushing allowing you to safely remove the magazine disconnect from the firearm. There are instructions on the internet showing the use of washers and other parts, but this is unreliable and unsafe! Use an actual part that is designed for the job. This bushing lets the hammer move properly and at the correct speed. You will be pleased with the fit and final result with this bushing. If you know how to clean this gun you can easily remove the disconnect. Removing the disconnect allows the magazines to fall free, allows them to seat properly and does allow the gun to fire with the magazine out for tactical competition and self-defense scenarios. Check to see if your state requires the magazine disconnect installed if the firearm is ever resold.
Supported Model List:MKIII™ -ALL MODELS!
- MKIII™ 22/45™
- MKIII™ 22/45™ Competition
- MKIII™ 22/45™ Government Target
- MKIII™ 22/45™ Target
- MKIII™ Competition
- MKIII™ Government Target
- MKIII™ Target
- MKIII™ LITE
- MKIII™ Hunter
*** ATTN: FAQ: Will this bushing work in my Volquartsen Hammer? YES. The bushing and VQ hammer will work together. However, it can be a tight fit to get them together. Please let us know if you are experiencing trouble and we will get you a bushing that will fit into the tighter VQ hammer.
Ruger® and its associated model names are registered trademarks of the Ruger® Corporation.
657 Reviews
-
Steel Ruger Mark III & 22/45 Magazine Disconnect Bushing
great product for the ruger mark 3 easy to install works great.
-
grand father
Part functions as advertised in two guns.
-
Magazine disconnect bushing
Super fast shipping along with perfectly machined bushing. Installation was a breeze with the supplied instructions.
-
Ruger Mark III or 22/45 hammer bushing to remove disconnect
Perfect machining, high polish, replaced dreaded mag safety in Mark III Target, also replaced sear and trigger with a match setup, now it is a civilized pistol, clean 2 lb pull, no more grittiness or 10 pound pull. Now it is easier to clean, all parts dropped in, highly satisfied, will buy more in future!
-
Works Perfectly
Product works perfectly!
-
Great Improvement for Mark III.
I have ordered and installed these in both a Mark III and a 22/45. The fit and finish are great. Instructions, along with the video are very helpful. The best part comes after installation. The magazines now "jump" out when released. A great feature and I highly recommend it.
-
Best "first" mod for the Mark III and 22/45's hands down
These make the magazines shoot right out when the mag release button is pressed as well as make it so that you don't have to mess around with the magazine insertion/removal steps during field stripping. I have used other aftermarket bushings in the past, and TandemKross' bushing meets or exceeds the quality of them. If I ever get another Mark III, I would not hesitate to order from them again. Great customer service, fast shipping, and lifetime warranty can't be beat.
-
Must have for the 22/45 Lite
SIMPLE to install in minutes, Installs PERFECT as advertised, allows you to remove the bar and spring for the mag safety which gives you the side effect of a better/smoother trigger and makes breaking the pistol down for cleaning a breeze! Don't hesitate one bit, get this, you won't regret it!!!
-
Best upgrade for the Mark III
Easy peasy. Once I got it apart, I had to clean it. It was nasty and with Murphy's Law, everything fell apart. Had to figure out how it went back together, still not a issue. Trigger feels lighter too. I had debated how doing this mod or not, but not because I was afraid of it. I figured I could live with the way Ruger built it, but I was wrong. Now those mags fly out.
