The Shadow Mount V3.0 is a Ruger® Mark IV™ red dot mount that fastens directly to the receiver using the factory receiver hole layout, so no picatinny rail or clamp sits between the optic and the gun. It fits across the Mark™ Series including the Mark IV™, Mark IV™ 22/45™, 22/45™ LITE, and Mark III™ models. It ships with all the necessary hardware to attach both the mount and the optic. Installation is simple and requires no machining or permanent modification to the pistol.
Who Should Use the Shadow Mount V3.0
Ideal Use Cases
- Steel Challenge or Rimfire Challenge Rimfire Pistol Open competitors, where optics are permitted and the time between plates largely comes down to how fast eye finds its target.
- Ruger® Mark™ Series owners who want to add an optic without drilling, tapping, or otherwise permanently modifying the receiver.
- Shooters with aging eyes or corrective lenses who find a single focal plane easier to work with than a three point iron sight picture.
- Owners of more than one Mark™ Series pistol, since the same mount design covers Mark IV™, Mark III™, and factory drilled and tapped Mark™ I and Mark™ II models with the standard receiver hole layout.
Shadow Mount V3.0 vs. Factory Sight and Mounting Options
Three ways to sight a Ruger® Mark™ Series pistol, and what separates them.
| Feature | TANDEMKROSS Shadow Mount V3.0 | Factory Rail Setup | Factory Iron Sights |
|---|---|---|---|
| Sight picture | One point of reference | One point of reference | Rear notch, front post, and target |
| Mounting method | Optic attaches to the mount, mount attaches to the receiver | Optic attaches to a rail adapter, rail adapter attaches to rail, rail attaches to the receiver | Sights fitted from the factory |
| Parts in the mounting stack | Two: the mount and the optic | Three: the rail, rail adapter/mount, and the optic | Front and rear sight |
| Optic height above bore | Lowest possible; varies depending on optic | Highest possible; height of picatinny rail plus height of rail mount/adapter and optic | No optic mounted |
| Interfaces that can shift under recoil | Two: optic to mount and mount to receiver | Three: optic to mount/adapter, mount/adapter to rail, and rail to receiver | Front and rear sight (unlikely); no optic mounted |
| Mounting hardware included | Receiver hardware and optic hardware both included | Varies by model and configuration | Not applicable |
Limitations to Know Before You Buy
- Three hole layout required: The mount fits Ruger® Mark™ Series models with the standard three hole layout. It does not fit model 40179 or vent rib models such as 43949. Check your model number before ordering.
- Optic footprint must be confirmed: The mount supports many popular optics from Vortex Optics®, Burris®, Trijicon®, Swampfox Optics, Holosun, and others, but not every footprint on the market. Use the compatibility chart linked on the product page to confirm your specific optic before ordering.
- Use a thread locker: The mounting screws should be installed with a thread locker and torqued carefully. Owners may experience screws backing out under repeated shooting when installed without thread locker, and over torquing small fasteners can strip the head of the screw.
- Division implications: When shooting in competitions like SASP, Rimfire Challenge, Steel Challenge, Metal Madness, or others, adding an optic can change which division your pistol is eligible for use within. Be sure to reference the rules of your particular league or range before making the decision to install an optic.
Technical Specifications
Construction
- Finish: Black anodized
- Body material: Aluminum
- Weight: 0.7oz without hardware (hardware depends on preferred optic)
- Mounting method: Direct to receiver using the factory three hole layout, no picatinny rail or clamp required; will only use two of the three mounting holes
- Hardware: Receiver mounting hardware and optic mounting hardware included
- Country of manufacture: USA
Compatibility
- Ruger® Mark IV™ Standard
- Ruger® Mark IV™ Tactical
- Ruger® Mark IV™ Target
- Ruger® Mark IV™ Hunter
- Ruger® Mark IV™ Competition
- Ruger® Mark IV™ 22/45™
- Ruger® Mark IV™ 22/45™ LITE
- Ruger® Mark IV™ 22/45™ Tactical
- Ruger® Mark III™ Standard
- Ruger® Mark III™ Target
- Ruger® Mark III™ Hunter
- Ruger® Mark III™ 22/45™
- Ruger® Mark III™ 22/45™ LITE
- Ruger® Mark III™ 22/45™ Target
- Ruger® Mark III™ 22/45™ Hunter
- Ruger® Mark™ I and Ruger® Mark™ II models that are factory drilled and tapped
Does not fit model 40179 or vent rib models such as 43949. TANDEMKROSS guarantees compatibility with factory Ruger® models in factory furniture and TANDEMKROSS original firearms. Compatibility with third-party receivers is not guaranteed.
Complete Package Includes
- Shadow Mount V3.0 for Ruger® Mark™ Series
- Hardware to attach the mount to the receiver
- Hardware to secure the optic to the mount
- Installation instructions available as a linked document on the product page
Shadow Mount V3.0 FAQs
What models are compatible with the Shadow Mount V3.0?
Yes, both are supported. The Shadow Mount V3.0 supports the Mark IV™ Standard, Tactical, Target, Hunter, and Competition along with the Mark IV™ 22/45™, 22/45™ LITE, and 22/45™ Tactical. Compatibility is determined by the receiver rather than the grip frame, which is why the same mount spans both the 1911 style 22/45™ frame and the standard Mark IV™ frame. The requirement is the standard three hole layout on top of the receiver. The Silencer Shop exclusive models (40179, 40181, 40182) and vent rib models such as 43949 are exceptions as they feature different hole patterns and are not compatible.
Does installing the Shadow Mount V3.0 require machining or permanent modification?
No, the Shadow Mount V3.0 does not require any machining, gunsmithing, or permanent modification. The mount uses mounting points already present on compatible receivers, so nothing needs to be drilled, tapped, milled, or permanently altered. Installation is easily done with the included hardware and tools. TANDEMKROSS provides written installation instructions plus an installation video on the product page. The pistol can be returned to its original configuration by removing the mount and reinstalling the factory hardware.
What factors help the Shadow Mount V3.0 maintain zero?
In practice, holding zero depends as much on installation technique as on the mount: use a thread locker on the mounting screws, torque them evenly, and verify zero at the range after any removal and reinstallation rather than assuming it. Owners who have installed the screws dry may experience them backing out under repeated shooting. Treat a zero check as part of the reinstallation process.
Which optics fit the Shadow Mount V3.0?
The Shadow Mount V3.0 accepts a wide selection of pistol red dots and reflex sights, including models from Vortex Optics®, Burris®, Trijicon®, Swampfox Optics, and Holosun. TANDEMKROSS publishes a compatibility chart on the product page so you can confirm your specific optic before ordering, which is the reliable step since footprints vary considerably even within a single brand's lineup. The mount ships with the hardware needed to secure the optic, so a standard installation does not require a separate mounting plate or hardware kit.
Legal and Compliance
No state level shipping restrictions apply to this product.
WARNING: This product can expose you to chemicals including chromium, which is known to the State of California to cause reproductive harm. For more information go to www.P65Warnings.ca.gov.
120 Reviews
-
great mounting plate
I used this mount plate on my Mark IV 22/45 to lower the optic to bore distance and it works great! Easy to install the plate on the pistol and easy to install the optic on the plate. It makes a huge difference in using the red dot on the pistol. Mounting the optic on the factory pic rail made the optic feel very high from the bore axis and awkward to use the red dot. This plate made a world of difference.
-
If you want a red dot, you gotta have this.
If there is one fault with Ruger .22 Mark IV handguns, it's when they include the long blocky pic rail on the rounded receiver and barrel. Put one on the Ruger Hunter and you've just uglied up a gorgeous gun. Most models come with excellent adjustable sights, but c'mon guys, the BIGGEST reason we buy a .22 is their phenomenal accuracy. That means if you want to shoot holes into holes at 25 yards, you need a red dot. Using the pic rail requires an additional mounting plate that adds even more height from the bore axis, not a good thing. Tandemkross has the ultimate solution with this perfect plate. It's minimum profile compliments the guns looks and keeps the height from bore axis low as possible. You get everything you need to mount any red dot except the tiny filler screws that you can buy from Ruger for four bucks. When you remove the pic rail, there are three holes on top of the receiver, and the mounting plate requires the two rear holes, so you need a filler plug for the front hole. (Important Note: The filler screws do not bottom out, so only install them until they are flush with the top receiver.) All of the Tandemkross install videos are excellent, so watch this one, but the installation is super easy. As they say, use Loctite Blue on all screws and you'll have a sight that stays put. Once you zero in, even your grandmother will shoot X-ringers all day.
-
Shadow Mount v3.0
Nice clean mount. Had all hardware needed to install.
-
SHADOW MOUNT V3.0 FOR RUGER® MARK™ SERIES
Very nice mount! Well made, looks good and perfect fit on my Ruger MK IV 22/45 Lite for attaching a Holosun red dot.
-
Shadow mount V3.0 for Ruger Mark IV
Perfect fit and it comes with everything you need to mount just about any optic, I mounted the Holosun 507COMP-GR which really makes this gun even more fun to shoot.
-
Worthless
This is worthless for any rmsc optic footprint. The screws are to thin and there are no post up front to secure the optic. Waste of money
-
Stream Demon
To mount a Cmore on the normal Ruger rail you need to buy their mount. this is a much better setup brings the dot down where it should be.
-
v3 mount plate
works good
-
Shadow Mount v3.0
Bought this mount to put a red dot on my Ruger MkIV. Works perfect and looks great. Everything came as described and shipped fast. The installation videos TandemKross has on their website have been very helpful. I’ll be buying more add ons for my Ruger soon.
