At a Glance:
- Machined from hardened tool steel to last a lifetime
- Unique positive “hook” design grabs casings securely and surely
- Reduces failures-to-eject and “stove-pipe” malfunctions
- TANDEMKROSS LIFETIME guarantee
The TANDEMKROSS Eagle’s Talon Extractor for Ruger® MK™ Series is a much needed reliability upgrade that replaces the stamped factory provided extractor. Often the factory extractor won't maintain a secure enough hold on the spent casing as the pistol is cycling and will case stove-pipes and failures-to-eject malfunctions. Luckily with this simple to install and affordable upgrade, you can greatly improve the reliability of your firearm! TANDEMKROSS "Eagle's Talon" Extractor is correctly machined with a positive hook that will grab and secure each round until it needs to be ejected. Eliminate your frustrations at the range with a much better part that will throw your spent cases far away from ever causing another failure-to-eject!
Supported Firearms:
- Ruger® Mark I™
- Ruger® Mark II™
- Ruger® Mark II™ 22/45™
- Ruger® Mark III™
- Ruger® Mark III™ 22/45™
- Ruger® Mark III™ 22/45™ LITE
- Ruger® Mark IV™ Target
- Ruger® Mark IV™ Hunter
- Ruger® Mark IV™ Competition
- Ruger® Mark IV™ Tactical
- Ruger® Mark IV™ 22/45™
- Ruger® Mark IV™ 22/45™ Tactical
- Ruger® Mark IV™ 22/45™ LITE
WARNING: This product can expose you to chemicals including cadmium, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov.149 Reviews
-
Rookie
We got the talon installed in both my wife's abd my 22/45, and shot last Tuesday, We were very happy how our guns shot. Her gun has been giving get fits so this is a huge improvement! Thanks Bryan and staff!
-
Mr
I was having problems with my Ruger Mark III Hunter where cases would not eject every 20 rounds or so. I ordered the " Eagle's Talon " extractor. Contact with Tandemkross was easy, promptly replied to and efficient. Shipping from the USA was quick and relatively inexpensive. Extractor was easy to install and after about 300 rounds, I have not yet had an FTE. Great product.
-
BUSINESS OWNER
GREAT PRODUCT!
-
Mr.
My Sr-22 rifle could not go through a mag without a stovepipe or double feed. I installed the Eagle's Talon extractor and spring and went to the range the same day. Shot around 100 rounds with not one problem. And this rifle had problems from day one. So if you have stovepipes or double feeds on your 10/22 this is the fix you need. Thanks again.
-
Eagle's Talon
Part works well in my Ruger MKIV. Had a bit of a struggle removing the old extractor and installing the new one, but once I did, I was happy with the result.
-
Eagle Talon Extractor
I have to give this one. I installed it in a Mark IV and there was hardly any lateral movement, it did not even move enough to clear the center under-cut area,ergo, the shell would of not came out. I installed/removed it 3 different times to rule out error. I then re-installed the original, and all was perfect again, so I left it. Because of this, I did not use the new firing pin either.
-
Better than factory or not
As far as better function than factory. It spits the spent shells out. But so did the factory one in my ruger. Is this one stronger and less likely to break. That I can't answer. But it is more refined in the looks department than the stamped out factory one. I choose to install it based on my son shooting in 4H matches. We had one competitor lose an extractor during the state shoot. So just to be on the safe side. With the amount of rounds that my ruger had fired in its life I felt it was time. Just based on the fact this extractor looks better built than the factory one. So far I'm pleased.
-
Mr.
Before installing the Eagle's Talon Extractor I was getting occasional failure to extract while shooting in Steel Challenge Match's. Since installing the Eagle's Talon I haven't had a single failure to extract. It was a good investment.
-
No more FTE
I installed this along with the LCI insert because I had issues with stovepipes and jams. I haven't been able to test this out a lot. The pit we shoot in is full of snow and it's been cold out. That being said, I put maybe 150 rounds through my 22/45 since installing this and the LCI insert and haven't had any problems with FTE or stovepipes. In hindsight, I wish I would have ordered the Gunsmither Pistol Pal (TK Part # 0801N0033SSL1). It was a bear to remove my old extractor with the tools I had on hand
