#NAME?

Eliminator Buck Mark Recoil Guide Rod by Striplin Custom Gunworks

Striplin Custom Gunworks

$22.99
(68 reviews) Write a Review
SKU:
2812N0310SSL1
Weight:
0.30 Ounces

Out of stock

 
At a glance:
  • Eliminates pesky C-clip
  • Simplifies maintenance and disassembly
  • Polished stainless steel for smooth cycling
The Browning Buck Mark is a popular rimfire pistol for shooting sports thanks to its reliability and performance. But even a good gun can be made great!
 
The new Eliminator Recoil Guide Rod for Buck Mark from Striplin Custom Gunworks is an aftermarket replacement for the factory Buck Mark guide rod, eliminating the C-clip used in the factory version that can cause reliability issues in the firearm. This one piece, machined stainless steel guide rod simplifies maintenance assembly and disassembly. The guide rod is made from hardened stainless steel and is polished for smooth cycling.
 
The Eliminator Buck Mark Recoil Guide Rod works with all Buck Mark pistols and rifles, including pre-2000 Buck Mark firearms. This replaces the guide rod only, and uses the factory spring and buffer. Watch the installation video from Striplin Custom Gunworks above for more features and to install the guide rod into your Buck Mark firearm.
 
*Please Note* Due to variations in Buck Marks, some light sanding/fitting may be required.
 
 
*Fits all Buck Mark models including the Buck Mark Rifle

68 Reviews

  • 5
    Eliminate Buckmark Guidrod

    Posted by AARON on 3rd Feb 2021

    Got tired of sending the c clip to space every time I did a deep clean that I avoided taking the gun apart for several years. I finally began having issues and needed a deep clean. Found this solution for not much more than a few of the c clips without the headache of trying to install a c clip with fat shaky fingers. Took a little bit of filling with the leatherman but once fitted worked flawlessly. I only have about 150 rounds on it but no issues to report so far. Would recommend to anyone with a buckmark.

  • 5
    review

    Posted by mahina on 26th Dec 2020

    I had been rather reluctant to take down my Buck Mark but after seeing the video and actually replacing the rod I feel reassured. Range time here is pretty limited due to the virus but can't wait to take the gun out.

  • 5
    Recoil Guide Rod

    Posted by Michael on 21st Dec 2020

    Well, I wasn't sure how this was going to work, having the guide rod captured in the slide without the retaining clip, but after installing it, I like that I don't need to mess with that little clip anymore. My Buckmark performs perfectly, I can't state enough that adding this with the other upgrades Tandemkross makes, I can definitely feel the difference on how my pistol performs and shoots. I really enjoy the videos, it's install one on one for dummies, and I couldn't do it with out it!! Thanks Tandemkross!! Keep up the good work

  • 5
    recoil rod

    Posted by Rick on 22nd Nov 2020

    Have not puy iy in yet, but looks like a lot better system than original setup.

  • 5
    Guide Rod

    Posted by Paul Brady on 11th Nov 2020

    This is absolutely the most useful of all the after-market parts. Just be sure to check the fit, and file off any excess length.

  • 5
    Recoil rod

    Posted by Jim on 3rd Nov 2020

    I brought this product to replace a factory rod. It is better made and has a good design. Be aware I had to file the end to make it fit properly in the gun.

  • 5
    Recoil Guide ROd

    Posted by John Slocomb on 31st Oct 2020

    The guide rod is a perfect addition to the Buck Mark pistol. Having the ability to use a paper clip to hold the spring in place is terrific and makes removing the rod very easy. Thanks for a great product.

  • 5
    Buckmark Recoil Rod

    Posted by Bob Hewitt on 5th Oct 2020

    I decided to get this after losing several 'C' rings on the Browing recoil rod. This item made complete disassembly a breeze - I highly recommend it. As stated, I had to do some fitting with 400-grit sandpaper. Sand and test, repeat until it fits.

  • 4
    As advertised

    Posted by Mike on 2nd Oct 2020

    No need to worry about losing the tiny C clip any more. Very well finished/polished for smooth action. Had to file about 1/32" off end to make it fit.

!