Install Instructions for Victory Trigger for Ruger® Mark III™, Mark III™ 22/45™, and Mark IV™ 22/45™
At a Glance:
- Textured and flat-faced for better control and feel
- 100% adjustable for pre- and over-travel
- Lightweight, skeletonized design
Supported Models:
- Ruger® Mark III™
- Ruger® Mark III™ 22/45™
- Ruger® Mark III™ 22/45™ LITE
- Ruger® Mark IV™ 22/45™
- Ruger® Mark IV™ 22/45™ LITE
- Ruger® Mark IV™ 22/45™ Tactical
The trigger of any firearm is critical and must give the shooter as much control as possible. The sleek, skeletonized, and lightweight design of the TANDEMKROSS Victory Trigger for Ruger® Mark III™ and 22/45™ provides a flat, textured face that many shooting pros prefer over a traditional curved trigger.
TANDEMKROSS’s unique design allows the shooter to pull straight back, making it easier for the shooter to tell if they are pulling too far left or right. The flat face also offers more real estate for the user to place their finger lower on the trigger. This increases their finger’s distance from the fulcrum, increasing leverage and decreasing the perceived trigger pull weight. While the actual pull weight technically never changes, having your finger further from the fulcrum or pivot still offers you a mechanical advantage.
Pairing this trigger with TANDEMKROSS’s Blast Pack (Thunder Hammer, Lightning Sear, and Blast Shield Magazine Disconnect) gets you an Ultimate Trigger Kit and is the best way to get you all the tactile and mechanical advantages of the Victory Trigger while also actually decreasing your pistol’s trigger pull weight. Please note, the Blast Pack and Ultimate Trigger Kit are only available for the Ruger® Mark IV™ and Ruger® Mark IV™ 22/45™ and is not compatible with the Ruger® Mark III™ or Mark III™ 22/45™.
All TANDEMKROSS Victory Triggers are textured for a no-slip grip in any condition, at any speed, even while wearing gloves!
The included pre-travel and post-travel screws allow for fine adjustment of trigger travel to create consistent, reliably clean trigger pulls. Amongst your included screws will be two different length pre-travel screws and two different length over-travel screws. You will want the longer pre- and over-travel screws if you are installing this trigger on a Mark IV™ 22/45™ and the shorter screws if installing in a Mark III™ or Mark III™ 22/45™.
The must-have TANDEMKROSS Victory Trigger for your Ruger® Mark III™ or 22/45™ pistol will bring any competition shooter one giant step closer to victory!
Need an extra hand to perform the install? Try the Magazine Vise Block for .22LR Platforms to keep your grip frame in place while performing this install or any routine maintenance!
Please note: This trigger does not work with any of the Standard Ruger® Mark IV™ pistols. Click here for a Victory Trigger for Ruger® Mark IV™.
This trigger is compatible with the Standard Ruger® Mark III™. However, due to the standard model’s smaller trigger guard, there is less space around the trigger which may be a concern for some users. Please be sure to watch our YouTube installation video above for more information. The trigger is shown in the video at timestamp 8:20.
Don’t forget, all TANDEMKROSS products are made in the USA and come with a LIFETIME guarantee!
WARNING: This product can expose you to chemicals including chromium, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov
364 Reviews
-
Mr
Well I have not installed yet. I bought a ton of your products for the same gun and have only been watching the video's over and over again to get a grasp on the whole project. I understand everything for the most part. However, on this product you have to put these two screws in that allow for adjustments but it looks like you have to completely dismantle it again to make the adjustments. Doesn't look like there is a way to access either screw without doing so.
-
Sir
I like the textured-face Victory trigger. It sure prevents any slipping of the finger. Installation was a piece of cake. Both the video and written instructions were crystal clear.
-
Trigger
All of the Tandemkross product that I have purchased so far have been great. This trigger is no different. It is easy to install & completely changes the feel for the better.
-
Great Trigger
Typical TK designed trigger. It functions just as the description states. I put a little black paint on the screw threads to hold them after setting the trigger limits. Works very well and feels better on the index finger.
-
none
I am very satisfied with the trigger - installation was simple (I took advantage of having the trigger assembly out to do a VERY thorough cleaning!) and the trigger feel is superb. I would like to find a similar one for my S&W M&P 9! How about a challenge, TK? A Victory Trigger for the M&P ...
-
Victory Trigger
Trigger was a snap to install. Results at the range were fantastic. Took out the excessive travel and reset. Flat trigger with aggressive texturing improves feel and feedback. Thanks TK.
-
Comp trigger
Easy install, excellent and consistent feel. Thanks TK!
-
Victory Trigger
The trigger install is reasonably simple and the TK videos give clear instruction. The trigger is an excellent upgrade that works as well as advertised. It definitely has helped with finger placement by providing tactile feedback when placement is off. At 67, this trigger (and a red dot mounted on the TK rail) have me now holing out the center of targets at 7 and 15 yards. Thanks TK.
-
Nice Trigger
It took about a hour to replace from the original trigger. I had a friend (pistol smith) follow the video step by step and just took his time. Went in pretty smooth. I had the stop screw set a little close at first and had to back it out just a little. (tells you that in the directions) If you have some problems with trigger consistency you might have the stop step to close. Once I had it set correct it works great! So much better than the factory trigger. Like all new triggers I just have to get used to it. Nice Job!
