Install Instructions for Victory Trigger for Ruger® Mark III™, Mark III™ 22/45™, and Mark IV™ 22/45™
At a Glance:
- Textured and flat-faced for better control and feel
- 100% adjustable for pre- and over-travel
- Lightweight, skeletonized design
Supported Models:
- Ruger® Mark III™
- Ruger® Mark III™ 22/45™
- Ruger® Mark III™ 22/45™ LITE
- Ruger® Mark IV™ 22/45™
- Ruger® Mark IV™ 22/45™ LITE
- Ruger® Mark IV™ 22/45™ Tactical
The trigger of any firearm is critical and must give the shooter as much control as possible. The sleek, skeletonized, and lightweight design of the TANDEMKROSS Victory Trigger for Ruger® Mark III™ and 22/45™ provides a flat, textured face that many shooting pros prefer over a traditional curved trigger.
TANDEMKROSS’s unique design allows the shooter to pull straight back, making it easier for the shooter to tell if they are pulling too far left or right. The flat face also offers more real estate for the user to place their finger lower on the trigger. This increases their finger’s distance from the fulcrum, increasing leverage and decreasing the perceived trigger pull weight. While the actual pull weight technically never changes, having your finger further from the fulcrum or pivot still offers you a mechanical advantage.
Pairing this trigger with TANDEMKROSS’s Blast Pack (Thunder Hammer, Lightning Sear, and Blast Shield Magazine Disconnect) gets you an Ultimate Trigger Kit and is the best way to get you all the tactile and mechanical advantages of the Victory Trigger while also actually decreasing your pistol’s trigger pull weight. Please note, the Blast Pack and Ultimate Trigger Kit are only available for the Ruger® Mark IV™ and Ruger® Mark IV™ 22/45™ and is not compatible with the Ruger® Mark III™ or Mark III™ 22/45™.
All TANDEMKROSS Victory Triggers are textured for a no-slip grip in any condition, at any speed, even while wearing gloves!
The included pre-travel and post-travel screws allow for fine adjustment of trigger travel to create consistent, reliably clean trigger pulls. Amongst your included screws will be two different length pre-travel screws and two different length over-travel screws. You will want the longer pre- and over-travel screws if you are installing this trigger on a Mark IV™ 22/45™ and the shorter screws if installing in a Mark III™ or Mark III™ 22/45™.
The must-have TANDEMKROSS Victory Trigger for your Ruger® Mark III™ or 22/45™ pistol will bring any competition shooter one giant step closer to victory!
Need an extra hand to perform the install? Try the Magazine Vise Block for .22LR Platforms to keep your grip frame in place while performing this install or any routine maintenance!
Please note: This trigger does not work with any of the Standard Ruger® Mark IV™ pistols. Click here for a Victory Trigger for Ruger® Mark IV™.
This trigger is compatible with the Standard Ruger® Mark III™. However, due to the standard model’s smaller trigger guard, there is less space around the trigger which may be a concern for some users. Please be sure to watch our YouTube installation video above for more information. The trigger is shown in the video at timestamp 8:20.
Don’t forget, all TANDEMKROSS products are made in the USA and come with a LIFETIME guarantee!
WARNING: This product can expose you to chemicals including chromium, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov
367 Reviews
-
Retired
This trigger is worth every penny it cost. I can pull it with one finger instead of two on my Ruger 22/45 Lite. Ernest5 Martin - Robinson
-
Just a shooter
Installation and adjustment was easy and simple HOWEVER both adjustment screws worked loose at less than 200 rounds. So much so that the overtravel adjustment screw prevented firing. This was cured using blue locktite but it would have been better if the setscrews had been the nylon threadlocker type. A few pennies more but worthwhile for what is otherwise a quality product. Chip King
-
Good Upgrade
I installed the trigger along with the sear. A vast improvement over what I thought was a horrible factory trigger. The texture on the trigger is a bit sharp for my liking but nothing I can't live with.
-
Trigger
The TK trigger for the Ruger mk iv 22-45 installed easily and works great.
-
Will
Cannot review at this time other than to say is looks great and price was good. My brand new Ruger Mk IV 22/45 is in the recall and I can not make any changes to grip frame until after the retrofit. However, I do have a friend that loves his trigger.
-
Mr.
Wonderful trigger. The feel and action is so much better than the stock trigger, and helps improve my target scores.
-
Mr
Totally easy to install. Adjust the screws with a magazine in the gun. Nice upgrade.
-
Awesome
I love the TK trigger, really easy to put in great for steel competitions, so much easier to control, just all around awesome!
-
mk2 upgrade
I installed this on my MK2 along with the volquartsen sear, now pulls at a snappy 2 1/4 lbs. It required some minor file work(this is only required on MK2) not hard at all. MAJOR IMPROVEMENT!!! Eric at TK is right there with all the answers. Good stuff, good people.
