Install Instructions for Victory Trigger for Ruger® Mark III™, Mark III™ 22/45™, and Mark IV™ 22/45™
At a Glance:
- Textured and flat-faced for better control and feel
- 100% adjustable for pre- and over-travel
- Lightweight, skeletonized design
Supported Models:
- Ruger® Mark III™
- Ruger® Mark III™ 22/45™
- Ruger® Mark III™ 22/45™ LITE
- Ruger® Mark IV™ 22/45™
- Ruger® Mark IV™ 22/45™ LITE
- Ruger® Mark IV™ 22/45™ Tactical
The trigger of any firearm is critical and must give the shooter as much control as possible. The sleek, skeletonized, and lightweight design of the TANDEMKROSS Victory Trigger for Ruger® Mark III™ and 22/45™ provides a flat, textured face that many shooting pros prefer over a traditional curved trigger.
TANDEMKROSS’s unique design allows the shooter to pull straight back, making it easier for the shooter to tell if they are pulling too far left or right. The flat face also offers more real estate for the user to place their finger lower on the trigger. This increases their finger’s distance from the fulcrum, increasing leverage and decreasing the perceived trigger pull weight. While the actual pull weight technically never changes, having your finger further from the fulcrum or pivot still offers you a mechanical advantage.
Pairing this trigger with TANDEMKROSS’s Blast Pack (Thunder Hammer, Lightning Sear, and Blast Shield Magazine Disconnect) gets you an Ultimate Trigger Kit and is the best way to get you all the tactile and mechanical advantages of the Victory Trigger while also actually decreasing your pistol’s trigger pull weight. Please note, the Blast Pack and Ultimate Trigger Kit are only available for the Ruger® Mark IV™ and Ruger® Mark IV™ 22/45™ and is not compatible with the Ruger® Mark III™ or Mark III™ 22/45™.
All TANDEMKROSS Victory Triggers are textured for a no-slip grip in any condition, at any speed, even while wearing gloves!
The included pre-travel and post-travel screws allow for fine adjustment of trigger travel to create consistent, reliably clean trigger pulls. Amongst your included screws will be two different length pre-travel screws and two different length over-travel screws. You will want the longer pre- and over-travel screws if you are installing this trigger on a Mark IV™ 22/45™ and the shorter screws if installing in a Mark III™ or Mark III™ 22/45™.
The must-have TANDEMKROSS Victory Trigger for your Ruger® Mark III™ or 22/45™ pistol will bring any competition shooter one giant step closer to victory!
Need an extra hand to perform the install? Try the Magazine Vise Block for .22LR Platforms to keep your grip frame in place while performing this install or any routine maintenance!
Please note: This trigger does not work with any of the Standard Ruger® Mark IV™ pistols. Click here for a Victory Trigger for Ruger® Mark IV™.
This trigger is compatible with the Standard Ruger® Mark III™. However, due to the standard model’s smaller trigger guard, there is less space around the trigger which may be a concern for some users. Please be sure to watch our YouTube installation video above for more information. The trigger is shown in the video at timestamp 8:20.
Don’t forget, all TANDEMKROSS products are made in the USA and come with a LIFETIME guarantee!
WARNING: This product can expose you to chemicals including chromium, which is known to the State of California to cause cancer. For more information go to www.P65Warnings.ca.gov
366 Reviews
-
Mr.
I sent this same message via email to TK. Great Us business. I frankly could not believe how much better shooting my Mark IV tactical was today after that trigger install especially without any other springs or sears or whatever. I like triggers to be around 4 pounds, and this felt lighter than that. I only shot my gun once out of the box and new immediately I needed to do something about the trigger. I started with this and thought I would have to get the VQ stuff as well. It was OK out of the box, but it shot darts today with ease on just the 2nd overall trip out with it. am totally good with the trigger action as it stands with just the Tandemkross trigger.
-
79407
I bought the victory trigger, blast shield, target sear, and a few other parts for my ruger and for the most part was very unimpressed. I ended up taking all tandem kross products off and going complete Volquartsen. The target sear I was sent was made for a mark 3 instead of the mark 4, luckily Volquartsen sent me the right part without question. Maybe it's just personal preference but the only Tandem Kross product left on my 22/45 lite is the game changer compensator.
-
Mr.
Excellent trigger! Very crisp. Just be patient with putting in the pre and over-travel screws, but once you get the dialed in SO worth it!
-
Mr.
An absolute must for your Ruger, love it. The TK video makes the install a breeze, anyone with even limited gunsmithing skills can do it. Another great product from TandemKross.
-
Nice touch
This makes shooting the ruger 22 pistol so much better... worth every penny. Easy to install too.
-
Mr
Yet Another Part I Am Having Installed By My Local Gun Smith Awaiting The Completion Of Said Project To See How This Improves The Weapons Performance
-
Great trigger
This trigger is so much better than I expected. My brother was saying it feels like a new gun with it.
-
Custom Look
Trigger looks great. Installed in a 22/45 Lite in all black except for this trigger in the chrome finish. Looks awesome with the after market grips in OD green, from stoner cnc. I watched the installation video several times before installing it went much quicker than I was expecting. Easy install and setup. Some reviews noted that the surface of trigger was to aggressive I didn't think so at all. I since have installed the Halo and love it as well as the mag disconnect blast shield also watched that video several times and install was easy when everything finally lined up. TK "Making Good Guns Great" is an under statement. Love the products and install info I will be ordering again.
-
Mr.
This trigger is awesome. Very easy install, easy to dial in. I use removable Loc-Tite to make sure the adjustment screws stay in place. Done. Watch the install video. I have about 500 rounds with it, no additional adjustment.
