Don't forget, all TANDEMKROSS MKIII™ series bushings come with a LIFETIME guarantee!
Steel Hammer Bushing for Mark III and 22/45 Pistols
- Magazines will slip right out
- Easier takedown and cleaning
- Can reduce failure to feeds
- Comes with colored installation instructions
This high quality 304 stainless steel bushing is made for high duty cycle shooting and replaces the Ruger® factory bushing allowing you to safely remove the magazine disconnect from the firearm. There are instructions on the internet showing the use of washers and other parts, but this is unreliable and unsafe! Use an actual part that is designed for the job. This bushing lets the hammer move properly and at the correct speed. You will be pleased with the fit and final result with this bushing. If you know how to clean this gun you can easily remove the disconnect. Removing the disconnect allows the magazines to fall free, allows them to seat properly and does allow the gun to fire with the magazine out for tactical competition and self-defense scenarios. Check to see if your state requires the magazine disconnect installed if the firearm is ever resold.
Supported Model List:MKIII™ -ALL MODELS!
- MKIII™ 22/45™
- MKIII™ 22/45™ Competition
- MKIII™ 22/45™ Government Target
- MKIII™ 22/45™ Target
- MKIII™ Competition
- MKIII™ Government Target
- MKIII™ Target
- MKIII™ LITE
- MKIII™ Hunter
*** ATTN: FAQ: Will this bushing work in my Volquartsen Hammer? YES. The bushing and VQ hammer will work together. However, it can be a tight fit to get them together. Please let us know if you are experiencing trouble and we will get you a bushing that will fit into the tighter VQ hammer.
Ruger® and its associated model names are registered trademarks of the Ruger® Corporation.
648 Reviews
-
Mr
Part does its job well. These guys sent me a custom replacement asap when the first one didn't fit the Volquaartsen trigger I had installed.
-
Great upgrade
Easy cheap upgrade that works! It gets rid of the mag safety easier when you need to take the gun apart and ejects the mags out better so your not have to reach and pull the mags out every time.
-
Worth it!
I installed two of these in a pair or MkIIIs and am quite pleased with the results. I did encounter an anomaly: My MKIIIs actually have older MkI styled sear springs in them from the factory. That made sliding the pin over to remove the hammer & mag disconnect and spring a little easier. Thing was, I accidentally pulled one pin out completely and couldn't figure out why my pistol's sear spring didn't match the instructions. I contacted Mr. Eric Paulson in tech support and after a couple of calls and emails, he helped me figure it out. In fact, the springs were a surprise to him, too. Bottom line? The bushings are a great addition to a pre-MkIV pistol. =)
-
Excellent addition
I put this in both my pistols. It makes the functionality of the pistol better and eases the takedown operation. I’m very pleased with it.
-
FIXED!
Eliminated two of the biggest issues I had with my 22/45. Perfect solution!
-
Me
Being able to remove that offensive magazine disconnect is beyond joyful. Part is well made, snugs things up a bit and well polished. Fit nice and easy.
-
competitor
Great product,have them in all my Rugers
-
Mr.
Don't know why I waited so long, makes take down, clean , and assembly so much easier. You don't have to mess with the magazine at all.
-
Tandemkross has excellent and high quality parts.
I am new to tandemkross with this being my first order. I can already tell with this one part and how well it works that all of their products will be worth using. This part was very easy to install and it did everything exactly as they said it would. The instructions and video are top notch. I will be a customer for life and I will hopefully be ordering more soon to continue to upgrade my 22/45. Thank you Tandemkross for the quality work that you have done.
